How do I pair my Ingenico card reader?

To pair your Ingenico iCMP card reader to your iPad

Ensure that your Ingenico iCMP card reader is adequately charged.
On the iPad, open settings and turn on Bluetooth.
Turn the Ingenico iCMP card reader on by pressing the power button on the right.
When BT Pairing Required message appears, press the F1 button.

In this regard, how do I reset my Ingenico card reader?

Hold down the clear button and the punctuation button (below the 9 key) at the same time for 3-5 seconds, until the terminal turns off. Once off, hold the enter button until the terminal powers on. Try the transaction again.

Furthermore, how do I connect Ingenico ISMP to iPad? Pair with the iPad

On the iPad, open the Settings app and tap 'Bluetooth'.
Toggle Bluetooth on.
Press the power button on the side of the iCMP to turn it on.
Wait about 30 seconds for 'BT Pairing Required' to appear on the iCMP screen, then press 'F1'.
Press 'F2' (down) and 'F3' (up) to select your iPad.

Furthermore, how do I pair my Ingenico Link 2500?

How to Connect and Use the Ingenico Link/2500

Turn on Bluetooth connection from Settings > Bluetooth on your iPad.
To pair, press 0, 0, 0, then 1 on the Link/2500.
Use the F3 button to go to 3 - Bluetooth Parameters.
Use the F3 button to go to 2 - Phone pairing.

How do I connect to iSMP4?

1.Connect the Ingenico iSMP4 terminal to your network

On your terminal's keypad, press the F key 5 times to access its Communications Settings.
Press F4 for Access Points.
Press F1 for New.
From the list, select your access point.
Select WPA/WPA2.
Enter your password followed by the green O key.

How do I connect my Ingenico to WiFi?

Power On WiFi

Scroll to and select 3-TDA (using the F2 button to scroll and Green button to enter)
Press 0 on the keypad to enter 0-Configuration.
Press 0 on the keypad to enter 0-Communication.
Press 3 on the keypad to enter 3-Wifi Settings.
Press 0 on the keypad to enter 0-Power.
Press 1 on the keypad to enter 1-ON.

How do you reset a visa machine?

How to reset your credit card machine / card terminal

On each terminal, press the MENU button twice and select F3 for SUPERVISOR.
Enter the password (normally 123456) and press ENTER. Then select F2 for PASSWORD and F2 again for MAC RESET.
Once you select the acquirer, the terminal will print out a report showing that the MAC has been reset.

Why is my credit card machine not printing?

No Print being displayed on the till roll – If the card machine till roll has no print facility, the till roll is in the wrong way. Simply remove the existing till roll from the card unit and turn it around and re-print. The paper should always be coming up from the lever.

How do I reset my Ingenico Lane 7000?

Press the red “X” key followed by the green enter key to save and reboot your settings.

How do I reset my Ingenico iPP320 card machine?

On the iPP320 PIN Pad, hold down the yellow key and press the punctuation key at the same time. The iPP320 PIN Pad will beep and restart.

How do I reset my ShopKeep card reader?

Hold the iCMP's power button for two seconds to reboot the reader. After the iCMP turns back on, pair it with the iPad. In the ShopKeep app, open the Main Menu and go to the 'Card Readers' screen. If there is a check next to the iCMP on this screen, troubleshooting is complete.

How do I reset my Ingenico Link 2500?

It may also be switch off by pressing simultaneously and (yellow key) for one second. In order to restart the terminal, press on the key- board. The card can be read either from bottom to top or from top to bottom, with the stripe facing the terminal.

How do I reset my link 2500?

Unpair the Link/2500 from the iPad.

Unpair the Link/2500 from the iPad.
Hold the '.,#*' and yellow buttons until the screen says 'Shutdown in progress'.
Hold the green button to turn the reader back on.
After the ShopKeep logo appears on the Link/2500, pair it with the iPad.

How do I connect my ShopKeep card reader?

Connect to ShopKeep

In ShopKeep, open the Main Menu and select 'Integrated Hardware'. Click to Enlarge.
Tap 'Card Readers'.
Tap the 'Ingenico' or 'iPP' device to connect.
If prompted, tap 'OK' and allow the reader to reboot.
In ShopKeep, wait for a checkmark to appear.

How do I connect my Ingenico card reader to my iPad?

Connect the iCMP:

Open the iOS 'Settings' application on your iPad.
Under 'Settings', tap on 'Bluetooth' and ensure Bluetooth is enabled before proceeding.
Power on the iCMP using the power button on the right side.
The reader should display 'BT Pairing Required'.

How do I connect Ingenico to my computer?

Connect hardware

Plug the connection cable's flat end into the payment terminal and secure it with the included screws.
Plug the power supply into the connection cable's round end.
Plug the connection cable's USB end into the back of the computer.
Plug the power supply into an electrical outlet.

How do I disable Ingenico iSMP?

Powering On/Off

To power on the iSMP, connect the battery and press green key.
To power off the iSMP, press pound (#) key + yellow key.